@Simemart he echo lo que me dices pero no entiendo nada... Esto me ha salido
Connecting...
Printer is now online.
>>> m122
SENDING:M122
X Y Z Z2 E
Address 0 0 0 0 0
Enabled false false false false false
Set current 800 800 800 800 800
RMS current 1436 1436 1436 1436 1436
MAX current 2025 2025 2025 2025 2025
Run current 25/31 25/31 25/31 25/31 25/31
Hold current 12/31 12/31 12/31 12/31 12/31
CS actual 0/31 0/31 0/31 0/31 0/31
PWM scale
vsense 0=.325 0=.325 0=.325 0=.325 0=.325
stealthChop false false false false false
msteps 256 256 256 256 256
interp false false false false false
tstep 0 0 0 0 0
PWM thresh.
[mm/s]
OT prewarn false false false false false
pwm scale sum 0 0 0 0 0
pwm scale auto 0 0 0 0 0
pwm offset auto 0 0 0 0 0
pwm grad auto 0 0 0 0 0
off time 0 0 0 0 0
blank time 16 16 16 16 16
hysteresis
-end -3 -3 -3 -3 -3
-start 1 1 1 1 1
Stallguard thrs 0 0 0 0 0
uStep count 0 0 0 0 0
DRVSTATUS X Y Z Z2 E
sg_result 0 0 0 0 0
stst * * * * *
olb
ola
s2gb
s2ga
otpw
ot
157C
150C
143C
120C
s2vsa
s2vsb
Driver registers:
X 0x00:00:00:00 Bad response!
Y 0x00:00:00:00 Bad response!
Z 0x00:00:00:00 Bad response!
Z2 0x00:00:00:00 Bad response!
E 0x00:00:00:00 Bad response!
Testing X connection... Error: All LOW
Testing Y connection... Error: All LOW
Testing Z connection... Error: All LOW
Testing Z2 connection... Error: All LOW
Testing E connection... Error: All LOW
Así tengo los puentes de debajo del driver
Connecting...
Printer is now online.
>>> m122
SENDING:M122
X Y Z Z2 E
Address 0 0 0 0 0
Enabled false false false false false
Set current 800 800 800 800 800
RMS current 1436 1436 1436 1436 1436
MAX current 2025 2025 2025 2025 2025
Run current 25/31 25/31 25/31 25/31 25/31
Hold current 12/31 12/31 12/31 12/31 12/31
CS actual 0/31 0/31 0/31 0/31 0/31
PWM scale
vsense 0=.325 0=.325 0=.325 0=.325 0=.325
stealthChop false false false false false
msteps 256 256 256 256 256
interp false false false false false
tstep 0 0 0 0 0
PWM thresh.
[mm/s]
OT prewarn false false false false false
pwm scale sum 0 0 0 0 0
pwm scale auto 0 0 0 0 0
pwm offset auto 0 0 0 0 0
pwm grad auto 0 0 0 0 0
off time 0 0 0 0 0
blank time 16 16 16 16 16
hysteresis
-end -3 -3 -3 -3 -3
-start 1 1 1 1 1
Stallguard thrs 0 0 0 0 0
uStep count 0 0 0 0 0
DRVSTATUS X Y Z Z2 E
sg_result 0 0 0 0 0
stst * * * * *
olb
ola
s2gb
s2ga
otpw
ot
157C
150C
143C
120C
s2vsa
s2vsb
Driver registers:
X 0x00:00:00:00 Bad response!
Y 0x00:00:00:00 Bad response!
Z 0x00:00:00:00 Bad response!
Z2 0x00:00:00:00 Bad response!
E 0x00:00:00:00 Bad response!
Testing X connection... Error: All LOW
Testing Y connection... Error: All LOW
Testing Z connection... Error: All LOW
Testing Z2 connection... Error: All LOW
Testing E connection... Error: All LOW
Así tengo los puentes de debajo del driver